Cabinet Saw Digital Readout Kits

DigiFence is a Digital Readout Kit for your Cabinet Saw Fence. This kit includes the digital scale, sensor, readout, and brackets. Don't see your fence type listed? We have dozens of other kits available; contact us for additional information.

Starting June 2022, these kits have a new installation method. To ensure the easiest and fastest installation we need to get a few bits of information from you. We will email you shortly after you place your order with a drawing that shows the information we need.

**Starting February 2024**, we have a new readout bracket in our kits. 



In stock
Product or Custom Design Question

DigiFence is a Digital Retrofit Kit for your existing cabinet saw rip fence.  Each system contains a digital measuring system, all the hardware needed to install DigiFence to your existing fence, installation instructions, and an operation manual. A typical DigiFence installation takes 25-30 minutes.

NOTE: Be sure to order DigiFence to fit your FENCE brand, not your SAW model.


  • 52 inch Measuring Range (Note: We can supply a 36 inch range or a 60 inch range at same price, but shipping costs may change.)
  • Readout digits are very large - 0.5 inches (12.7 mm) tall!
  • Readings change from decimal inches, millimeters, or fractions (1/16, 1/32, 1/64) with a single button press
  • Easy to calibrate - start at zero or ANY preset starting position
  • Battery operation - 1 CR123 Lithium battery lasts 8-12 months
  • Upgrades are available for ranges up to 120 inches
  • MADE IN THE USA since 1989


  • Accuracy: ± 0.003 inch with factory supplied readout.
  • Repeatability: +/- 0.001 inch
  • Measuring Range: 36, 52, or 60 inches for the price shown. (52" is the default. If you want a different size, just add a note in the SHIPPING COMMMENTS box after you ADD TO CART.)
  • 1 year warranty.

About lifting your fence off:

  • If you regularly lift your fence off the table, we have a HINGE KIT that allows the fence to be taken off in seconds, and reinstalled in seconds.
  • When used properly, this does not cause data loss or a need to re-calibrate.

About calibrating:

  • DigiFence can be calibrated two ways:
    1. Move fence against saw blade (machine power off).
      Press the DATUM on the readout.
      (This method is not recommended if you are after best possible accuracy and repeatability.)
    2. Move fence close to the saw blade and lock it in place.
      Cut a small board, using same feed/speed as you normally do.
      Measure the cut board with best tool possible.
      Set this value into the digital readout using the PLUS and MINUS keys. 
      Why is this better? It accounts for any wobble, runout of your blade. It accounts for any vibration in your saw. It removes any questions about squareness of the fence to the blade.
      Simply put: It gets you the best accuracy possible!

About shipping costs:

  • Our website calculates shipping cost based on the product's weight only
  • In some cases, the length of our package can increase the shipping rate. NOTE: Our electronic scales are made in a single, rigid beam to ensure best possible accuracy and longest lifetime possible.
  • Shipping to residential addresses increases shipping cost with UPS.
  • When we receive and process your order, we hunt for the best rate possible, so shipping costs can sometimes be lower than the cart calculates. In this case, we refund the difference to you by mailed check.



If your fence model is not listed, please contact us; new models are being engineered all the time and we have dozens of models archived!

DigiFence installation on SawStop fence:

NOTE: As of 6-1-2022, we have a new kit design that fits many fence types. Installation is now much faster and requires fewer tools. If interested in the new kit, please call or email us for more details.

Write Your Own Review
You're reviewing:Cabinet Saw Digital Readout Kits